International Fibreboard Casecode |
This code
which is prepared in collaboration with ESBO (The European Solid Board
Organisation), contains a methodical presentation of all existing box
design styles, a code number being assigned to each design. As a
reference document, the code is used world-wide and it has been adopted
by the United Nations.
Symbols used in drawings and computer systems. Unless otherwise specified all dimensions are expressed as internal dimensions in mm as follows: Length (L) x Breadth (B) x Height (H) Length (L) the longer dimension at the opening Breadth (B) = the shorter dimension at the opening Height (H) -the dimension from the top of the opening to the base The dimensions L B. H are specified in each description of the case construction, for some models the numerical value of B can exceed the numerical value of L. Dimensions should be measured under standard climate conditions, on the flat blank from the centre of crease bearing the thickness of the material in mind. For telescope type boxes the height (h) of the upper part (lid) should be given as a fourth measurement after an oblique stroke, i.e. 355 x 205 x 120/40 mm (L) (B) (H) (h) For cases with overlapping outer flaps the length of the area of overlapping (o) should be given as a fourth measurement after an oblique stroke. i.e. 355 x 205 x 120/ 40 mm (L) (B) (H) (o) Sheet dimensions Unless otherwise specified, the dimensions of a corrugated sheet are expressed in mm as follows: 1st dimension x 2nd dimension 1st dimension=along the glue lines 2nd dimension =across the glue lines Style versions Several case types may have derived versions without the necessity to create a new style. In this case a suffix should be added to the basic style number separated by a dash. Example 0201-2. Aversion maybe unique to individual manufacturers. Combination of types The construction styles shown are of the basic types of fibreboard cases. If the ultimate construction is a combination of two or three basic models. e.g. flap arrangements, they may also be described as follows: Top flaps as 0204, Bottom flaps as 0215 This type may also be described as 0204/0215 (Top flaps. Bottom flaps). 0204 0215 0204/0215 Styles and the manufacturers joint The drawing style layouts as shown in this Code may need to be re-arranged depending on the Manufacturers Joint chosen. Some styles may have a Manufacturers Joint which maybe glued, stitched or taped. A glued or stitched Joint may be an extension of either the short or the long panel. The sketches show how these would be indicated on a drawing: This applies to all designs in this Code. Manual of Automated erection Each design style includes one of the following indications M - usually manual erection A - usually automated erection M/A - can be either manual or automated M+A - requires a combination of both These indications are based on current practice and are intented to give additional information to specifiers and users Some manually erected cases can be closed automatically (e.g : 0216 or 0712) Correct and effective closure of the packages is as important as the packaging construction itself. The following methods of closure are possible either singly or in combination:
Closure by stiching This can be done according to the example shown General Remarks Please note that several case designs contained in the Code under a specific number could also be classified under other basic type groups. Commercial rolls and sheets. Slotted-type boxes consist of basically one piece with a glued, stitched or taped manufacturers joint and top and bottom flaps. They are shipped flat, ready to use and require closing using the flaps provided. Description : 0202 Slotted-type boxes consist of basically one piece with a glued, stitched or taped manufacturers joint and top and bottom flaps. They are shipped flat, ready to use and require closing using the flaps provided. Description : 0205 Slotted-type boxes consist of basically one piece with a glued, stitched or taped manufacturers joint and top and bottom flaps. They are shipped flat, ready to use and require closing using the flaps provided. Description : 0207 Description : 0208 Slotted-type boxes consist of basically one piece with a glued, stitched or taped manufacturers joint and top and bottom flaps. They are shipped flat, ready to use and require closing using the flaps provided. Description : 0211 Slotted-type boxes consist of basically one piece with a glued, stitched or taped manufacturers joint and top and bottom flaps. They are shipped flat, ready to use and require closing using the flaps provided. Description : 0215 Slotted-type boxes consist of basically one piece with a glued, stitched or taped manufacturers joint and top and bottom flaps. They are shipped flat, ready to use and require closing using the flaps provided. Description : 0218 Slotted-type boxes consist of basically one piece with a glued, stitched or taped manufacturers joint and top and bottom flaps. They are shipped flat, ready to use and require closing using the flaps provided. Description : 0227 Slotted-type boxes consist of basically one piece with a glued, stitched or taped manufacturers joint and top and bottom flaps. They are shipped flat, ready to use and require closing using the flaps provided. Description : 0230 Slotted-type boxes consist of basically one piece with a glued, stitched or taped manufacturers joint and top and bottom flaps. They are shipped flat, ready to use and require closing using the flaps provided. Telescope-type boxes consist of more than one piece and are characterised by a lid and/or bottom telescoping over the body of the box. Description : 0301 Description : 0302 Telescope-type boxes consist of more than one piece and are characterised by a lid and/or bottom telescoping over the body of the box. Description : 0304 Description : 0306 Telescope-type boxes consist of more than one piece and are characterised by a lid and/or bottom telescoping over the body of the box. Description : 0308 Description : 0309 Telescope-type boxes consist of more than one piece and are characterised by a lid and/or bottom telescoping over the body of the box. Description : 0312 Description : 0313 Telescope-type boxes consist of more than one piece and are characterised by a lid and/or bottom telescoping over the body of the box. Description : 0320 Description : 0321 Telescope-type boxes consist of more than one piece and are characterised by a lid and/or bottom telescoping over the body of the box. Description : 0323 Description : 0325 Telescope-type boxes consist of more than one piece and are characterised by a lid and/or bottom telescoping over the body of the box. Description : 0331 Description : 0350 Telescope-type boxes consist of more than one piece and are characterised by a lid and/or bottom telescoping over the body of the box. Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0400 Description : 0402 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0403 Description : 0405 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0406 Description : 0410 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0411 Description : 0413 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0415 Description : 0420 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0421 Description : 0423 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0424 Description : 0426 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0427 Description : 0429 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0430 Description : 0432 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0433 Description : 0435 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0436 Description : 0440 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0441 Description : 0443 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0444 Description : 0446 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0447 Description : 0449 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0450 Description : 0452 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0453 Description : 0455 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0456 Description : 0458 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0459 Description : 0470 Folder-type boxes and trays usually consist of only one piece of board. The bottom of the box is hinged to form two or all side walls and the cover. Locking tabs, handles, display panels etc., can be incorporated in some designs. Description : 0471 Description : 0473 Slide-type boxes consist of several pieces of liners and sleeves sliding in different directions into each other. This group also includes outside sleeves for other cases. Description : 0503 Slide-type boxes consist of several pieces of liners and sleeves sliding in different directions into each other. This group also includes outside sleeves for other cases. Description : 0511 Slide-type boxes consist of several pieces of liners and sleeves sliding in different directions into each other. This group also includes outside sleeves for other cases. Rigid-type boxes consist of two separate end pieces and a body and require stitching or a similar operation before they can be used. Description : 0605 Rigid-type boxes consist of two separate end pieces and a body and require stitching or a similar operation before they can be used. Description : 0608 Rigid-type boxes consist of two separate end pieces and a body and require stitching or a similar operation before they can be used. Description : 0616 Rigid-type boxes consist of two separate end pieces and a body and require stitching or a similar operation before they can be used. Description : 0621 dy-glued cases consist of basically one piece, are shipped flat and ready to use by simple setting up. Description : 0701 Description : 0703 dy-glued cases consist of basically one piece, are shipped flat and ready to use by simple setting up. Description : 0712 Description : 0713 dy-glued cases consist of basically one piece, are shipped flat and ready to use by simple setting up. Description : 0715 Description : 0716 dy-glued cases consist of basically one piece, are shipped flat and ready to use by simple setting up. Description : 0718 Description : 0747 dy-glued cases consist of basically one piece, are shipped flat and ready to use by simple setting up. Description : 0751 Description : 0752 dy-glued cases consist of basically one piece, are shipped flat and ready to use by simple setting up. Description : 0761 Description : 0770 dy-glued cases consist of basically one piece, are shipped flat and ready to use by simple setting up. Description : 0772 Description : 0773 dy-glued cases consist of basically one piece, are shipped flat and ready to use by simple setting up. Category : 09Interior fitments such as inside liners, pads, partitions, dividers etc, whether tied to Case Design or as singular items. Any shown number of panels is arbitrary and may be increased or decreased as required. Coding of interior fitmentsThe following range of interior fitments is coded depending on the number of panels used, in any combination of shapes (for computer systems). Description : 0903 Description : 0904 Description : 0905 Description : 0906 Category : 09Interior fitments such as inside liners, pads, partitions, dividers etc, whether tied to Case Design or as singular items. Any shown number of panels is arbitrary and may be increased or decreased as required. Coding of interior fitmentsThe following range of interior fitments is coded depending on the number of panels used, in any combination of shapes (for computer systems). Description : 0910 Description : 0911 Description : 0913 Description : 0914 Category : 09Interior fitments such as inside liners, pads, partitions, dividers etc, whether tied to Case Design or as singular items. Any shown number of panels is arbitrary and may be increased or decreased as required. Coding of interior fitmentsThe following range of interior fitments is coded depending on the number of panels used, in any combination of shapes (for computer systems). Description : 0920 Description : 0921 Description : 0929 Description : 0930 Description : 0931 Description : 0932 Description : 0933 Montage : M 60/65 Category : 09Interior fitments such as inside liners, pads, partitions, dividers etc, whether tied to Case Design or as singular items. Any shown number of panels is arbitrary and may be increased or decreased as required. Coding of interior fitmentsThe following range of interior fitments is coded depending on the number of panels used, in any combination of shapes (for computer systems). Description : 0941 Description : 0942 Description : 0943 Description : 0944 Category : 09Interior fitments such as inside liners, pads, partitions, dividers etc, whether tied to Case Design or as singular items. Any shown number of panels is arbitrary and may be increased or decreased as required. Coding of interior fitmentsThe following range of interior fitments is coded depending on the number of panels used, in any combination of shapes (for computer systems). Description : 0948 Description : 0949 Description : 0950 Description : 0951 Category : 09Interior fitments such as inside liners, pads, partitions, dividers etc, whether tied to Case Design or as singular items. Any shown number of panels is arbitrary and may be increased or decreased as required. Coding of interior fitmentsThe following range of interior fitments is coded depending on the number of panels used, in any combination of shapes (for computer systems). Description : 0970 Description : 0971 Description : 0972 Description : 0973 Category : 09Interior fitments such as inside liners, pads, partitions, dividers etc, whether tied to Case Design or as singular items. Any shown number of panels is arbitrary and may be increased or decreased as required. Coding of interior fitmentsThe following range of interior fitments is coded depending on the number of panels used, in any combination of shapes (for computer systems). The terms Box, Container and Case are interchangeable in the context of these descriptions. |